Category
- Abrasives
- Adhesives & Sealants
- Automotive
- Bearings & Transmissions
- Cabinets & Racking
- Calipers & Gauges
- Catering Equipment & Supplies
- Cleaning & Hygiene
- Collets & Toolposts
- Computers & Accessories
- Counterboring & Spot Facing
- Cutting Tools
- Bandsaws & Hacksaws
- Countersinking
- Deburring
- Hole Making
- Milling
- Ball Nose
- Carbide B/N End Mills – Long Series
- Carbide B/N End Mills – Regular Series
- Carbide B/N End Mills – Short Series
- Carbide B/N Slot Drills – Long Series
- Carbide B/N Slot Drills – Regular Series
- HSS B/N Slot Drills – Long Series
- HSS B/N Slot Drills – Short Series
- HSS-Co. B/N Slot Drills – Long Series
- HSS-Co. B/N Slot Drills – Short Series
- Bore Milling
- End Mills
- Carbide Double Ended End Mills – Regular Series
- Carbide End Mills – Long Series
- Carbide End Mills – Regular Series
- Carbide End Mills – Short Series
- HSS End Mills – Long Series
- HSS End Mills – Short Series
- HSS-Co. End Mills – Long Series
- HSS-Co. End Mills – Regular Series
- HSS-E PM End Mills – Regular Series
- Indexable Bodies
- Key & Slot Cutters
- Milling Inserts
- Roughing/Ripper Cutters
- Slot Drills
- Carbide Slot Drills – Double Ended
- Carbide Slot Drills – Long Series
- Carbide Slot Drills – Regular Series
- Carbide Slot Drills – Short Series
- HSS Slot Drills – Long Series
- HSS Slot Drills – Short Series
- HSS-Co. Slot Drills – Long Series
- HSS-Co. Slot Drills – Regular Series
- HSS-Co. Slot Drills – Short Series
- Slot Drill Cutter Sets
- Special Geometry Cutters
- Throwaway Cutters
- Ball Nose
- Part off & Grooving
- Reamers
- Reference/Data Books
- Threading
- Die nuts
- Dies
- Indexable
- Tapping Hand
- BA ISO529 HSS-GT Taps
- BSF ISO529 HSS-GT Taps
- BSPF ISO529 HSS-GT Taps
- BSPT ISO529 HSS-GT Taps
- BSW ISO529 HSS-GT Taps
- Combination Drill/Taps
- Left Hand ISO529 HSS-GT Taps
- Metric Coarse ISO529 HSS-GT Taps
- Metric Fine ISO529 HSS-GT Taps
- Metric ISO529 HSS-GT Threading Sets
- NPSF ISO529 HSS-GT Taps
- NPT ISO529 HSS-GT Taps
- NPTF ISO529 HSS-GT Taps
- Tap Wrenches
- UNC ISO529 HSS-GT Taps
- UNF ISO529 HSS-GT Taps
- Tapping Production
- Thread Chasers
- Turning
- Display Material
- Fasteners
- Fluid & Water Control
- Fluid Power
- Furniture
- Hand Tools
- Building & Construction
- Carpenters & Joiners
- Auger; Forstner & Flat Bits
- Bradawls; Gimlets & Tacklifters
- Chalk Lines
- Hand Drills & Braces
- Hole Cutters
- Marking & Cutting Gauges
- Mitre Blocks & Bench Hooks
- Pincers
- Planes
- Saws – Coping; Fret & Flexisaws
- Saws – Gents; Dovetail & Tenon
- Saws – Hand & Mitre
- Squares; Rules & Bevels
- Surface Forming Tools
- Wood Chisels
- Wood Turning & Carving Tools
- Clamps
- Cutting & Sawing
- Cycle Tools
- Decorators
- Electrical
- Engineers Tools
- Gardeners & Contractors
- Keys & Drivers
- Measuring
- Non Sparking Tools
- Pliers & Grips
- Plumbing & Pipe Tools
- Riveters
- Screwdriver Bits
- Screwdrivers
- Screwdrivers – Cabinet Handle
- Screwdrivers – Electronics & Mini
- Screwdrivers – Fluted Handle
- Screwdrivers – Hi-Grip/Mechanics Style Handle
- Screwdrivers – Insulated Handle
- Screwdrivers – Offset/Double Ended
- Screwdrivers – Precision/Jewellers
- Screwdrivers – Protorq/Magnum Style Handle
- Screwdrivers – Spiral Ratchet/Yankee
- Sheet Metal Working
- Sockets (Hand)
- Sockets (Impact)
- Spanners & Wrenches
- Stencils & Engraving
- Striking Tools
- Tool Kits & Multi Tools
- Torque Tools
- Vices
- Lubricants & Chemicals
- Anti Seize Lubricants
- Chain; Drive & Rope Lubricants
- Corrosion Preventatives & Welders Anti-Spatter
- Food Industry Lubricants & Greases
- Greases
- Grinding Fluids
- Hot Dip Coatings
- Industrial Cleaners & Solvents
- Leak Detectors; Flawfinders & Freezer Sprays
- Lubricating and Penetrating Oils
- Marker Paints & Pens
- Metal Cutting Coolants
- Mould Release Agents
- Paints & Primers
- Tapping & Drilling Lubricants
- Water Displacing & Maintenance Oils
- Materials & Maintenance
- Measuring & Test Equipment
- Co-Ordinate Measuring Machines
- Electrical Measuring & Testing Equipment
- Environment Gauges
- Inspection Workholding
- Mechanical Gauges
- Non-Mechanical Gauges
- Optical Equipment
- SPC & Digital Readout Equipment
- Spring Calipers & Spring Dividers
- Surface/Hardness Testers
- Test Gauges & Accessories
- Weigh Scales
- Office Supplies & Stationery
- Packaging
- Pads & Accounts
- Personal Protection
- Clothing & Workwear
- Eye Protection
- Footwear
- Hand Protection
- Gloves – Cold Resistant
- Gloves – Cotton
- Gloves – Cowhide
- Gloves – Disposable
- Gloves – Extra Grip
- Gloves – Goatskin
- Gloves – Latex
- Gloves – Leather
- Gloves – Mixed Fibre
- Gloves – Nitrile
- Gloves – Polkadot
- Gloves – Polyurethane
- Gloves – PVC
- Gloves – Rigger
- Gloves – Stockinette
- Gloves – Terry Towelling
- Gloves – Vinyl
- Gloves – Welders Gauntlets
- Head & Face Protection
- Hearing Protection
- Knee & Elbow Pads
- Personal Protection Kits
- Respiratory Protection
- Piston & Valve Tools
- Power Tools
- Site Safety
- Spindle Nose & Workholding
- Steps & Access Equipment
- Storage & Handling
Blog
Relaunch Promotion
Product Showcase
ELECTRO MAGNETIC DOOR CLOSER CE PLATED
Door Furniture
This comprehensive range of Door Controls feature varying power sized units for many different door applications. They come with a choice of architectural covers which are each available in 26 different plated or colour coated finishes.
To help select the correct closer for you, each unit has a listing showing their key features, certification numbers and fire ratings. Plated arms are available on certain units only, and test certificates are available upon request.
BS EN1154 Classification
This standard classifies door closers using a 6 digit coding system. Each digit relates to a particular feature of the product measured against the standards performance requirements.
Digit (1) – Category of use:
?3? denotes the unit is for closing doors from at least 105.
?4? denotes the unit is for closing doors from 180 open.
Digit (2) – Durability:
?8? successfully completed 500,000 test cycles.
Digit (3) – Test door mass/size:
Seven grades are identified as shown in the table below (where a
closer provides a range of power sizes both the minimum and
maximum sizes shall be shown):
Power size Test door mass Recommended door leaf width
1 20kg 750mm
2 40kg 850mm
3 60kg 950mm
4 80kg 1100mm
5 100kg 1250mm
6 120kg 1400mm
7 160kg 1600mm
Digit (4) – Fire behaviour:
?0? denotes the unit is NOT suitable for use on fire/smoke doors.
?1? denotes the unit IS suitable for use on fire/smoke doors.
Digit (5) – Safety in use:
?1? all door closer units are required to stisfy the essential requirement of safety in use.
Digit (6) – Corrosion-resistance:
?0? – indicates no defined corrosion-resistance,
?1? – indicates mild corrosion-resistance,
?2? – indicates a moderate level of corrosion-resistance,
?3? – indicates high corrosion-resistance,
?4? – indicates very high corrosion-resistance.
Within this section units have been tested to BS EN1154, with many units also having been tested to current Certifire testing and CE test criteria. Therefore, the 6 digit classification is shown against each of the varying units, thus indicating their performance and grading under BS EN1154.
An example of the grading for a 1559 closer unit would be as follows:
3 8 4/2 1 1 3
(1) (2) (3) (4) (5) (6)
Out of stock
SKU : MTL9494060K
Door Furniture
This comprehensive range of Door Controls feature varying power sized units for many different door applications. They come with a choice of architectural covers which are each available in 26 different plated or colour coated finishes.
To help select the correct closer for you, each unit has a listing showing their key features, certification numbers and fire ratings. Plated arms are available on certain units only, and test certificates are available upon request.
BS EN1154 Classification
This standard classifies door closers using a 6 digit coding system. Each digit relates to a particular feature of the product measured against the standards performance requirements.
Digit (1) – Category of use:
?3? denotes the unit is for closing doors from at least 105.
?4? denotes the unit is for closing doors from 180 open.
Digit (2) – Durability:
?8? successfully completed 500,000 test cycles.
Digit (3) – Test door mass/size:
Seven grades are identified as shown in the table below (where a
closer provides a range of power sizes both the minimum and
maximum sizes shall be shown):
Power size Test door mass Recommended door leaf width
1 20kg 750mm
2 40kg 850mm
3 60kg 950mm
4 80kg 1100mm
5 100kg 1250mm
6 120kg 1400mm
7 160kg 1600mm
Digit (4) – Fire behaviour:
?0? denotes the unit is NOT suitable for use on fire/smoke doors.
?1? denotes the unit IS suitable for use on fire/smoke doors.
Digit (5) – Safety in use:
?1? all door closer units are required to stisfy the essential requirement of safety in use.
Digit (6) – Corrosion-resistance:
?0? – indicates no defined corrosion-resistance,
?1? – indicates mild corrosion-resistance,
?2? – indicates a moderate level of corrosion-resistance,
?3? – indicates high corrosion-resistance,
?4? – indicates very high corrosion-resistance.
Within this section units have been tested to BS EN1154, with many units also having been tested to current Certifire testing and CE test criteria. Therefore, the 6 digit classification is shown against each of the varying units, thus indicating their performance and grading under BS EN1154.
An example of the grading for a 1559 closer unit would be as follows:
3 8 4/2 1 1 3
(1) (2) (3) (4) (5) (6)
Specification :
Brand : Matlock
Description : Covered Unit
eCl@ss Code : 23219090
Finish : Plated
Supplier Part No. : IN9198 PLATED
UNSPSC Code : 31162800
Weight | 1 kg |
---|
Related products
-
6mm SQUARE x 300mm KEY STEELRead more
Kennedy Industrial Key Steel – Square: Metric
Square â Metric
High grade mild steel. Available in square or rectangular sections. Metric manufactured from: BS4235 Part 7 1972 grade steel equivalent to DIN 6885.
Inch manufactured from: BS46 PART 7 1958 grade steel.
Length: 300mm and 12â.
Other sizes available on request. -
2mm SQUARE x 300mm KEY STEELRead more
Kennedy Industrial Key Steel – Square: Metric
Square â Metric
High grade mild steel. Available in square or rectangular sections. Metric manufactured from: BS4235 Part 7 1972 grade steel equivalent to DIN 6885.
Inch manufactured from: BS46 PART 7 1958 grade steel.
Length: 300mm and 12â.
Other sizes available on request. -
3mm SQUARE x 300mm KEY STEELRead more
Kennedy Industrial Key Steel – Square: Metric
Square â Metric
High grade mild steel. Available in square or rectangular sections. Metric manufactured from: BS4235 Part 7 1972 grade steel equivalent to DIN 6885.
Inch manufactured from: BS46 PART 7 1958 grade steel.
Length: 300mm and 12â.
Other sizes available on request. -
14 x 9 x 300mm RECTANGULAR KEY STEELRead more
Kennedy Industrial Key Steel – Rectangular: Metric
Rectangular â Metric
High grade mild steel. Available in square or rectangular sections. Metric manufactured from: BS4235 Part 7 1972 grade steel equivalent to DIN 6885.
Inch manufactured from: BS46 PART 7 1958 grade steel.
Length: 300mm and 12â.
Other sizes available on request.