Archives: Products
Showing 22577–22592 of 23773 results
-
SMC303 300x350mm MAINTENANCE PILLOWS (BOX-16)Read morePLUS Absorbent Pillows
Medium weight design with coverstock for added strength – The “Workshop Essential”. A mid to high end, balanced solution. Optimised for increased absorption per-pad.
⢠The mid-range, all-round choice for onsite spill management
⢠Medium weight design featuring single-side coverstock for added strength and tear resistance
⢠Low-lint release for a cleaner job
⢠Multiple perforations for improved productivity. Performance and endurance, combined. Legal compliance, assured
⢠Works with Spill Depot to ensure site compliance and fast access
â¢Hazard level: Moderate to high
â¢Typical spill volume: Medium
â¢Frequency of use: Medium to high⢠Maintenance – Absorbs All Fluids – Grey/Black
For use with water based fluids spills and non-aggressive chemicals and oils. Not suitable for use on water
⢠Oil-Only – Repels Water – White
Hydrophobic absorbent can be used on water. Will float even when oil laden
⢠Chemical (Universal) – Yellow
For use with water based fluids and aggressive chemicals, oils and solvents. Not suitable for use on water -
SMK35Y MAINTENANCE CARRYBAG SPILLKIT 35LTRRead more35 ltr Kits in Cube Bag
Many situations require a permanent supply of absorbents to be on hand. Solent Plus⢠spill kits are a cost-effective answer to this requirement. Available in Maintenance, Oil-only and Chemical kits, they range in capacity from 10ltr up to 240ltr. They are packed with sufficient absorbents to cope with a spill up to the size shown.
Kits contain:
⢠15 x Solent Prime pads (1.0 ltr/pad)
⢠2 x Solent Plus 3.0m sock (10 ltr/sock)
⢠1 x Disposal bag and tie (LUT-741-6430
⢠1 x Instruction sheet⢠Maintenance – Absorbs All Fluids – Grey/Black
For use with water based fluid spills and non-aggressive chemicals and oils. Not suitable for use on water.
⢠Oil-Only – Repels Water – White
Hydrophobic absorbent can be used on water. Will float even when oil laden.
⢠Chemical (Universal) – Yellow
For use with water based fluids and aggressive chemicals, oils and solvents. Not suitable for use on water. -
SMP501 500x400mm MAINTENANCE PADS (BOX-50)Read moreESSENTIALS Light Weight Absorbent Pads
Performance and endurance combined in a lightweight design. A straightforward and highly cost effective solution to spill control.
⢠Designed to be simple and without unnecessary frills
⢠Especially suited to low-volume, high-frequency use
⢠Ideal replacement for granules
⢠Lint-free
⢠Works with Spill Depot to ensure site compliance and fast access.
⢠Hazard level: Low to moderate
⢠Typical spill volume: Low
⢠Frequency of use: High⢠Maintenance – Absorbs All Fluids – Grey/Black
For use with water based fluid spills and non-aggressive chemicals and oils. Not suitable for use on water.
⢠Oil-Only – Repels Water – White
Hydrophobic absorbent can be used on water. Will float even when oil laden.
⢠Chemical (Universal) – Yellow
For use with water based fluids and aggressive chemicals, oils and solvents. Not suitable for use on water. -
SMP504 500x400mm MAINTENANCE PADS (BOX-200)Read moreESSENTIALS Light Weight Absorbent Pads
Performance and endurance combined in a lightweight design. A straightforward and highly cost effective solution to spill control.
⢠Designed to be simple and without unnecessary frills
⢠Especially suited to low-volume, high-frequency use
⢠Ideal replacement for granules
⢠Lint-free
⢠Works with Spill Depot to ensure site compliance and fast access.
⢠Hazard level: Low to moderate
⢠Typical spill volume: Low
⢠Frequency of use: High⢠Maintenance – Absorbs All Fluids – Grey/Black
For use with water based fluid spills and non-aggressive chemicals and oils. Not suitable for use on water.
⢠Oil-Only – Repels Water – White
Hydrophobic absorbent can be used on water. Will float even when oil laden.
⢠Chemical (Universal) – Yellow
For use with water based fluids and aggressive chemicals, oils and solvents. Not suitable for use on water. -
SMS230 MICROMETER STANDRead moreKennedy® Micrometer Stand – Standard Type
Made of cast iron, it is designed for use with most standard micrometers up to 100mm (4″). The clamp has positive angular and padded parallel clamping jaws.
-
SNKN 1204-ENN INSERT GRADE QP25Rp275.000Read moreYamaloy Indexable Milling Inserts – SNKN
QP25 (P25) – Uncoated. For medium and finish milling of steels.
-
SNMG 120404-NM7 INSERT GRADE QX520Read moreIndexable Turning Inserts – SNMG
Grades:
QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.
QX530 (ISO P25-P35 M15-M25) Coated.- Turning grade for Steels, Cast Steels and Stainless Steels. A good general purpose Steel grade for roughing.
QX5030 (ISO P20-P40 M20-M30) CVD Coated. – Medium / rough turning and intermediate cutting of steel / stainless steel. Combination of toughest substrate and alumina coating (MT-TiCN + TiC + AL2O3 + TiN) having superior chipping resistance provide wide coverage.Chip Breaker: NM6. Application: Med Cut.
Chip Breaker: NM7. Application: Med/Rough.
Chip Breaker: NR8. Application: Rough.
Chip Breaker: NR9. Application: Rough. -
SNMG 120408-NM6 INSERT GRADE QX5030Rp207.000Add to cartIndexable Turning Inserts – SNMG
Grades:
QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.
QX530 (ISO P25-P35 M15-M25) Coated.- Turning grade for Steels, Cast Steels and Stainless Steels. A good general purpose Steel grade for roughing.
QX5030 (ISO P20-P40 M20-M30) CVD Coated. – Medium / rough turning and intermediate cutting of steel / stainless steel. Combination of toughest substrate and alumina coating (MT-TiCN + TiC + AL2O3 + TiN) having superior chipping resistance provide wide coverage.Chip Breaker: NM6. Application: Med Cut.
Chip Breaker: NM7. Application: Med/Rough.
Chip Breaker: NR8. Application: Rough.
Chip Breaker: NR9. Application: Rough. -
SNMG 120408-NM7 INSERT GRADE QX520Read moreIndexable Turning Inserts – SNMG
Grades:
QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.
QX530 (ISO P25-P35 M15-M25) Coated.- Turning grade for Steels, Cast Steels and Stainless Steels. A good general purpose Steel grade for roughing.
QX5030 (ISO P20-P40 M20-M30) CVD Coated. – Medium / rough turning and intermediate cutting of steel / stainless steel. Combination of toughest substrate and alumina coating (MT-TiCN + TiC + AL2O3 + TiN) having superior chipping resistance provide wide coverage.Chip Breaker: NM6. Application: Med Cut.
Chip Breaker: NM7. Application: Med/Rough.
Chip Breaker: NR8. Application: Rough.
Chip Breaker: NR9. Application: Rough. -
SNMG 120408-NR8 INSERT GRADE QX520Read moreIndexable Turning Inserts – SNMG
Grades:
QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.
QX530 (ISO P25-P35 M15-M25) Coated.- Turning grade for Steels, Cast Steels and Stainless Steels. A good general purpose Steel grade for roughing.
QX5030 (ISO P20-P40 M20-M30) CVD Coated. – Medium / rough turning and intermediate cutting of steel / stainless steel. Combination of toughest substrate and alumina coating (MT-TiCN + TiC + AL2O3 + TiN) having superior chipping resistance provide wide coverage.Chip Breaker: NM6. Application: Med Cut.
Chip Breaker: NM7. Application: Med/Rough.
Chip Breaker: NR8. Application: Rough.
Chip Breaker: NR9. Application: Rough. -
SO-COOL AEROSPACE M/PURPOSE WATER SOLUBLE OIL 20LRead moreSolent “Plus” General Purpose Soluble Cutting Oil
Sophisticated lubricant chemistry. Excellent rust/staining protection. Low residue and good mix stability. Controls foam in high pressure fluid delivery applications. Outstanding bio-resistance. Excellent surface finishes and extended tool life. Preserves parts and equipment. Clean running operation. Specially formulated for use in both hard and soft waters. Extended service life/lower treatment costs.
Recommended concentrations:
General Machining 5% or (a dilution of 20 to 1). Heavy duty machining 10% or (a dilution of 10 to 1).
Available in grade SC-AERO.
Supplied in 20 litre stacking poly container and 205 litre barrel. -
SO-COOL ALUMINIUM WATER SOLUBLE OIL 20LTRRead moreSolent “Plus” Water Soluble Oil
Semi-synthetic, environmentally improved ? does not contain sodium nitrite, phenols, triazene, PTBBA or chlorinated additives. Enhanced sump life and excellent anti-foam characteristics. Optimum tool life on the most arduous operations. Excellent corrosion protection and lubrication to cutting areas, machine fixtures, slides etc. Low emulsion odour.
Low drag out losses. Easily removed in splash areas. Resists the formation of aluminium soaps – Improves filtration and machine cleanliness.
Recommended concentrations:
General machining 7% or (a dilution of 14 to 1).Heavy duty machining 10% or (a dilution of 10 to 1).
Available in grade SC-ALU.
Supplied in 20 litre stacking poly container or 205 litre barrels. -
SO-COOL CAST IRON WATER SOLUBLE OIL 20LTRRead moreSolent “Plus” Water Soluble Oil
Semi-synthetic formulation. Excellent anti-foam characteristics. Environmentally improved – does NOT contain sodium nitrite, phenols or chlorinated additives. Excellent sump life and corrosion protection. Superb tramp oil rejection characteristics. Enhanced tool tip life. Low drag-out loss – highly cost effective in use. Based on highly refined mineral oil. Increased detergency.
Recommended concentrations:
General machining 5% or (a dilution of 20 to 1). Arduous operations/difficult materials 7% or (a dilution of 14 to 1). Grinding 3% or (a dilution of 33 to 1). -
SO-COOL GP HARD/SOFT WHITE WATER SOLUBLE OIL 20LRead moreSolent “Plus” General Purpose Soluble Cutting Oil
Environmentally improved – does NOT contain phenols, boron, triazene, PTBBA or chlorinated additives. Based on highly refined mineral oils. High degree of machine tool lubrication. Ideal for a wide range of machining operations. Low odour. Low unit cost. Specially formulated for use in both hard and soft waters.
Recommended concentrations:
General machining 7% or (a dilution of 14 to 1). Grinding (surface, cylindrical centreless) 2 – 3% or (a dilution of 2% 50 to 1 or 3% 33 to 1).
Available in grade SC-GP.
Supplied in 20 litre stacking poly containers and 205 litre barrels. -
SO-COOL GRINDING SYNTHETIC WATER SOLUBLE OIL 20LTRRead moreSolent “Plus” General Purpose Soluble Grinding Oil
Fully synthetic formulation. Long working life therefore economical. Minimises wheel glazing. Effective corrosion resistance. Stable emulsions in soft and hard water. Does not contain PTBBA.
Recommended concentration for general machining operations:
Grinding Cast iron 2 % to 3.5% or (a dilution of 50 to 1 or 30 to 1).
Steel and Ni/Cr steel 2% or (a dilution of 50 to 1).Available in grade SC-GS.
Supplied in 20 litre stacking poly container. -
SO-COOL STAINLESS STEEL WATER SOLUBLE OIL 20LTRRead moreSolent “Plus” General Purpose Soluble Cutting Oil
Environmentally improved – does NOT contain phenols, boron,
triazene, PTBBA or chlorinated additives. Based on highly refined mineral oils. High degree of machine tool lubrication. Ideal for a wide range of machining operations. Low odour. Low unit cost. Stable emulsions in very soft and very hard water.
Recommended concentrations:
General Machining 7% or (a dilution of 14 to 1). Heavy duty machining 10% or (a dilution of 10 to 1).
Available in grade SC-INOX.
Supplied in 20 litre stacking poly container and 205 litre barrel.